How To Install A Shower Head?

Have you ever been in the shower and the water is just beginning to shoot you from all directions in the face because the holes in the head of the shower are being blocked? So if you are in the same predicament, you might be surprised to find out that the only thing that is wrong with your shower is cleaning the shower head. Do not worry about how to clean shower head.

Doesn’t your shower head perform as usual? Mineral deposits can build up over time, which can cause the nozzles to squirt water in all directions or totally block up, leaving you with bad water pressure or low flow.

A thorough cleaning may be necessary for such situations. as cleaning your shower head is essential because mineral deposits from water build up in the shower head holes. These minerals will obstruct your shower head and stop the flow of water to its complete capacity.

Collect your tools and Cleaner

One way to clean your showerhead is to remove it from the pipe and soak it in vinegar. This is what you are going to require for this technique:

Pot, bucket or another container that is big enough to accommodate the showerhead, Distilled white vinegar Wrench and an ancient rag. An ancient Soft cloth-like microfiber or flannel.

1st Step

Remove the showerhead by counter-clockwise twisting it. If you have trouble twisting it, attempt to wrap an old rag around the linking nut and twist it with a wrench. The rag will assist to safeguard your showerhead’s surface.

Consider using a smaller container that fits the showerhead; use less vinegar. A tiny bucket or plastic bin can also be used. Cover the showerhead, fill the pot with enough white vinegar. The vinegar’s acids will assist in dissolving the showerhead’s white mineral deposits.

Many heads of the shower have flexible nozzles of rubber. By merely massaging each nozzle with your finger, you can dislodge mineral build-up in these nozzles. You can also use a toothbrush to scrub the nozzles softly.

2nd Step

Garnish some baking soda in the bath. For each cup of vinegar that you pour into the tub, you should pour about 1⁄3 of a cup of baking soda. The solution is expected to burst

You can then fill a plastic bag with vinegar and wrap it around the shower head if you prefer to leave the shower head connected to the pipe that comes out of the wall. Secure the bag with a rubber band, tape, or twist tie around the head.

Leave the bag for a few hours around the head of the shower. Remove the bag and switch on the water to clear the vinegar from the head of the shower for a few minutes.

You can submerge the shower head in a container full of white vinegar if you don’t mind removing the head from the shower pipe. Let the shower head soak for a couple of hours in the vinegar. Re-attach the head of the shower to the shower pipe and for a few minutes run water through the head to clear the vinegar.

3rd Step

Take the showerhead and rinse it. You should see the flaking off mineral deposits.

Use an ancient toothbrush to remove any residue. Focus on the foundation of the holes; this is where the most mineral build-up is going to be. Gently scrub the brush and rinse with cool water over any residue. Continue to do this until all residues are gone.

Use a soft tissue to polish the showerhead. A microfiber tissue or even a piece of flannel can be used. Wipe the showerhead gently with the cloth until it is totally dry and no water places are available.

Return the showerhead to the pipe of the wall. Wrap a plumbing tape around the threaded portion of the wall pipe in the opposite direction, then screw the showerhead back on. Turn the water on for a few moments in your shower. This will wipe out any residue not received by the toothbrush.

Turn off the water and use a smooth cloth to polish the showerhead. You can use a flannel or a microfiber cloth. Buff the showerhead surface gently with the cloth until it’s dry and you can’t see any water spots anymore.

4th Step

In a plastic bag, put white vinegar. When you tie the bag to the shower, you should pour in enough to cover the head of the shower entirely. Make sure the bag is free of holes and can support the vinegar’s weight for a longer period of time.

Pour in the bag some baking soda. For every cup of vinegar you pour into the tub, you should pour about 1⁄3 of a cup of baking soda. The solution is supposed to burst.

Raise the plastic bag to the head of the shower while attached. Hold in your hands the plastic bag open. Raise it to the head of the shower so that the head of the shower is totally overwhelmed.

Tie off the bag’s top. A zip tie, a rubber band, or even an elastic hair can be used. Make sure the bag is linked so you can let go of it without the bag dropping. Wait for an hour at least. You can leave the vinegar bag for a deeper cleaning overnight as well.

Remove the bag of plastic. Throw away the plastic bag and the vinegar. Run the shower for a couple of minutes until it no longer smells like vinegar. Your shower is supposed to be cleaner and run better.

5th Step

Use a remover for the lime scale. Try CLR or Simple Green products. Follow the directions for removing mineral deposits from the shower head on the item itself. Clean the stains of rust. Use a rust removing officer, like Bar Keeper’s Friend, to wipe off rust stains if your shower head is rusty. For persistent rust, use a toothbrush or scouring pad

Wipe down the shower head’s exterior. Use a fundamental cleaning agent to wash the outside of your shower head, such as 409 or Scrubbing Bubbles. Sprinkle the solution onto a cloth or toothbrush and clean by side.

Clean the screen

Remove the display from the filter. Typically, the filter screen is on the portion of the shower connecting to the pipe. Usually, it is rather tiny and circular. Clean the screen for the filter. Run for a few minutes under running water. With a toothbrush, scrub it. Make sure that the filter screen leaves all debris.

Final Verdict

Keep your shower head flowing freely with these simple cleaning steps by removing mineral deposits such as lime scale. Doing natural shower-cleaning with the use of ingredients such as vinegar and baking soda can be a great way to make your bathroom look great.

Cleaning the head of your shower is also good for the health of your family. Wet surroundings such as the one inside a shower head are bacteria breeding grounds. It is therefore important to follow the above steps for a better result.

Recent Articles

9 Best Bathroom Air Fresheners Review and Buying Guide

Bathrooms are typically small confined rooms that are bound to smell unpleasant once in a while. It doesn’t matter how promptly you clean up...

How to Remove Shower Drain Cover

Introduction Shower drain covers are very important in preventing small things like razor blades, small pieces of jewellery, hairpins etc. from going down the drain....

Is Your Shower Drain Clogged? Here are 8 Ways to Prevent It!

Clogging in shower drains happen due to various reasons. The usual culprits include hair, skin cells, grease, and soap. These clogs do not happen...

How to Clean Shower Drains – A DIY Guide to Maintaining Drain Hygiene

You woke up early in the morning to get a quick shower, but your bathroom is practically flooding in murky, soapy water. We have...

Best Hand Dryers Reviews with Buying Guide

Paper towels reigned over the commercial industry for quite a while. Then came automated hand dryers that revolutionized the way we used to get...

Related Stories

LEAVE A REPLY

Please enter your comment!
Please enter your name here